SECTION MASTER FORMAT 1995 - 10510 MASTER FORMAT 2004 - 10 51 43 WIRE MESH LOCKERS ** NOTE TO SPECIFIER ** WireCrafters; storage lockers. This section is based on the products of WireCrafters, LLC, which is located at: 6208 Strawberry Lane Louisville, KY 40214-2900 Tel: (800) 626-1816 Tel: (502) 363-6691 Fax: (502) 361-3857 www.wirecrafters.com WireCrafters' solid steel and woven wire storage lockers are ideal for secured storage areas in large rooms or under utilized areas, where lockers will add efficiency to the storage area, secure stored items, and eliminate clutter. WireCrafters also makes traditional partitions, industrial barriers to separate work areas, railings to enclose open sides of mezzanines, and wire mesh enclosures for pallet racks, which are not included in this section. PART 1 GENERAL 1.1 SECTION INCLUDES A. Wire mesh storage lockers B. Solid sheet metal bulk storage lockers. 1.2 RELATED SECTIONS ** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required. A. Section 09900 - Paints and Coatings: Field painting. 1.3 SUBMITTALS A. Submit under provisions of Section 01300. B. Product Data: Manufacturer's printed data on products to be furnished. 1. Shop Drawings: Complete layout and fabrication drawings. C. Samples: Finish color samples for selection. D. Keys: Turn over keys for door locks to Owner at completion of project. PART 2 PRODUCTS 2.1 MANUFACTURER A. Acceptable Manufacturer: WireCrafters, LLC; 6208 Strawberry Lane, Louisville, KY 40214-2900. ASD. Tel: (800) 626-1816 or (502) 363-6691. Fax: (502) 361-3857. www.wirecrafters.com Email: info@wirecrafters.com ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions. B. Substitutions: Not permitted. C. Requests for substitutions will be considered in accordance with provisions of Section 01600. 2.2 STORAGE LOCKERS A. Storage Lockers: Factory-assembled modular sized door and divider panels bolted together, complete with all components, accessories, hardware, and fasteners; interchangeable units that allow expansion without waste of components. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. 1. Style: Single tier. 2. Style: Double tier. 3. Style: Single and double tier, in arrangement shown on drawings. ** NOTE TO SPECIFIER ** Delete two of the following three paragraphs. 4. Width: 36 inches (915 mm). 5. Width: 48 inches (1220 mm). 6. Width: _________________ ** NOTE TO SPECIFIER ** Delete three of the following five paragraphs. 7. Depth: 36 inches (915 mm). 8. Depth: 48 inches (1220 mm). 9. Depth: 60 inches (1524 mm). 10. Height: 90 inches (2286 mm). 11. Height: ___________________ ** NOTE TO SPECIFIER ** The following three paragraphs are optional. 12. Provide tops of same construction as panels. 13. Provide backs where lockers are not to be installed against a wall; 20 gauge galvanized steel sheet. 14. Provide formed steel sheet bottoms. 15. Finish: Electrostatic sprayed enamel, in manufacturer's standard color. 16. Provide appropriate hardware for fastening panels together and anchoring in place. ** NOTE TO SPECIFIER ** Delete either B. or C. below. B. Wire Mesh Panels: Steel angle frames with wire mesh securely welded in place; factory drilled holes for fasteners. 1. Wire Mesh: 10 gauge, 0.135 inch (3.5 mm) steel wire woven into 1 by 2 inch (25 by 50 mm) rectangular mesh. 2. Door Frames: 1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle. 3. Wall Frames: 1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle on three sides, 1/8 inch by 3 inch (3 mm by 76 mm), steel flat on fourth side. 4. Single Tier Doors: 1/4 by 3/4 inch (6 by 19 mm) steel bar stiffener securely welded to frame behind mesh. 5. Doors: Factory pre-hung; 2-1/2 by 2-1/2 inch (63 by 63 mm) spun pin hinges, welded in place; door strike and padlock hasp. C. Solid Sheet Metal Panels: Steel angle frames with sheet metal securely welded in place; factory drilled holes for fasteners 1. Sheet Metal: 16 gauge 0.0598 inch hot rolled sheet 2. Door Frames: 1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle. 3. Wall Frames: 1-1/4 by 1-1/4 by 1/8 inch (32 by 32 by 3 mm) hot rolled steel angle on three sides, 1/8 inch by 3 inch (3 mm by 76 mm), steel flat on fourth side. 4. Single Tier Doors: 1/4 by 3/4 inch (6 by 19 mm) steel bar stiffener securely welded to frame behind mesh. 5. Doors: Factory pre-hung; 2-1/2 by 2-1/2 inch (63 by 63 mm) spun pin hinges, welded in place; door strike and padlock hasp. 6. Optional Three Point Locking system. D. Dividers and Bottoms: 16 gauge galvanized steel sheet, formed to provide extra strength and rigidity. 1. Dividers: Anchor to supports bolted to wall panels, at 45 inches (1143 mm) above floor. PART 3 EXECUTION 3.1 INSTALLATION A. Install in accordance with manufacturer's instructions. B. Install plumb, level, and securely anchored to floor and to other structural members where indicated, shim where necessary. C. Adjust doors smooth, easy operation. END OF SECTION